Q: Can the storage tank be mounted horizontally as well as vertical?
A: Yes the tank can be installed in all positions.
Q: I am using a Miracle Oil Additive that is supposed to eliminate wear on start up so why would I need to install Insta-Lube System?
A: There are a lot of oil additives that claim to eliminate some wear by depositing a film of lubricant on the bearings surfaces.
But none of this will pressurize and adjust the hydraulic valve lifters or positively separate bearing surfaces with pressurized oil like the Insta-Lube Pre lube system.
Q: I have a 1956 Cadillac Coupe Deville and want to keep the same engine appearance; can the tank be mounted remotely?
A: Yes the kit will work on your Caddy; the hose is long enough to place the tank and valve out of site so everything looks stock.
Q: I am rebuilding a 350 Chevy and will install the kit; can the tank be filled with oil ready to prelube the very first startup?
A: Yes the Accumulator can be filled with oil ready to pre lube the engine for the first time.
Q: I have a Winnebago motor home with a 440 CID V8 Engine will the preluber work on this engine as well as my four-cylinder Nissan?
A: Yes the pre oil kit will work on all internal combustion engines.
Q: It's a well-known fact that a great deal of Motor Bearing Wear is at startup, so why don't the engine manufactures address the problem?
A: The engine manufactures know that the engines will wear out faster without pre-lubing, it is called planed obsolescence to sell more replacement engines.
Q: Will it work on my motor home?
A: Because there are 4 kit sizes to choose from, there is a kit just right for all Cars, trucks, suvs, vans, motor homes, boats, tractors, stationary engines and motors.
Q: How good is the Insta-Lube Pre Lube System in cold weather?
A: This is an area that is especially important as a lot of wear takes place on cold startups, our customers in Iceland really appreciate the Insta-Lube kits.
By installing the Insta-Lube pre-oil Kit you eliminate most of this bearing wear and prolong the life of your engine.
Q: How difficult is the Insta-Lube Pre Lube kit to install?
A: There are 3 easy steps to install the Insta-Lube Kit
1. Bolt on the mounting bracket with 2 bolts or self-tapping screws.
2. Connect the hydraulic hose between engine and storage tank.
3. Connect 12 volt positive wire to selected fuse and solenoid valve.
Q: Will the Pre Lube kit be any help in preventive maintenance for my cab?
A: The Insta-Lube System will benefit all engines, some more than others.
Since you have multiple startups daily it will make a substantial reduction in overall engine wear.
Q: Will installing the kit void my engine warranty?
A: Your warranty will not be affected by installing the AutoEngineLube kit.
According to the MAGNUSON-MOSS WARRANTY ACT OF 1975 installing aftermarket equipment does not void a vehicle manufacturer's original warranty.
Q: After installing the Insta-Lube Kit will there be less emission?
A: Yes, the pre-adjusted hydraulic valve Lifters will have the engine tuned for maximum efficiency and less emissions.
However the primary benefit to the engine is eliminating the wear to the Main bearings, Rod bearings, Camshaft bearings, Pistons, Piston Rings, and Wrist pens, Cylinder Walls, Hydraulic Valve Lifters, Timing Gears, and Timing Chains during startup.
Q: I have a 1951 Pontiac that uses a 6-volt electrical system will the pre-luber work on it?
A: Yes our kits will work on all 12-volt 24-volt and 6-volt systems.
Q: Is the oil that is stored in the accumulator tank filtered oil?
A: Yes, only pre-filtered oil from the engine oil gallery is stored for pre-lubing the engine the next time you turn the key on.
|
